********************************************************************************************

    Release Notes for Vigor2600V Series

    Firmware Version    : v2.5
    Release Date        : November 22, 2003

    Applied Models      : Vigor2600V, Vigor2600Vi, Vigor2600VG, and Vigor2600VGi

********************************************************************************************

[Introduction]

The Vigor2600V series is a new product family which includes Vigor2600V, Vigor2600Vi,
Vigor2600VG and Vigor2600VGi model.  This product family is based on the same hardware architecture
of the whole new Vigor 2600plus series router and integrate VoIP function into the router.

For more details of the product information, please visit our websites on http://www.draytek.com/


[Release Firmware]

(1)For Annex A Model,
	     1> "v26va250.xxx" is with ADI firmware 42E2EA53.  (Standard)

	     2> "v26vk250.xxx" is with ADI firmware 41E2BE2C.       
                 (Recommended for UK, v2.5_UK)

	     3> "v26v0250.xxx" is with ADI firmware 43E2EAA1.
                 (Recommended for high dB users which are using 
                  ADSL extended line on UK, v2.5_UK2)

	     4> "v26vc250.xxx" is with ADI firmware 40E2BE29.       
                 (Recommended for Holland, v2.5_H)

(2)For Annex B Model,
	     1> "v26vb250.xxx" is with ADI firmware 40E3BE15.  (Standard)

	     2> "v26vg250.xxx" is with ADI firmware 40E4BE3d.	  
                 (Recommanded for Germany, v2.5_G)

Notes:
 
1. You have to upgrade "*.RST" firmware file once you face the booting problems 
after upgrading.  After upgrade "*.RST" firmware file to the router, it will erase the existing settings 
of the router, and restore the factory default settings into the router.  
What is the timing to using "*.rst" file to upgrade your router?  
Once you failed to upgrade your router using "*.ALL" firmware file (normally use) several times, then we suggest you use "*.RST" firmware file to do the upgrade.  

2. After upgrade the router successfully, you can make sure the upgraded firmware version is the one listed above from the router's web user interface. 

3. Do not attempt to restore old settings from a configuration backup file downloaded 
from previous firmware version.  


[Release Note]

This release firmware versioin was based on Vigor2600 series Rev. v2.5, besides, this revision we 
have added some additional functions listed below: 

1. LPR Print Server via USB Printer port on the back panel

2. VLAN support port-based rate throttle capability

3. The Multi-PVC function is mainly to improve the ADSL access capability.  
Current implementation depends on specific ISP/Telcom services.  If you don't know whether 
your ISP/Telcom support it or not, please ignore the realted settings of Multi-PVC function.  
In general, you are recommended to select "UBR" of QoS for the Internet Access.

4. If you have any ADSL on-line problem, please contact your service provide at first, 
or get into web user interface ("Internet Access Setup" > "PPPoE/PPPoA" or "MPoA") to change 
the "Modulation" of "DSL Modem Settings" to "T1.413", then to try again.  Also, you can use 
the following Telnet commands to tune your router working with Globespan chipset DSLAM :

  > adsl status            Get DSLAM chipset verdor information
  > adsl dslam gspn        Set ADSL parameters compatible with the Globespan chipset DSLAM 
  > adsl dslam default     Set ADSL parameters to fatory default settings

5. Under Development
   - Bandwith Management Facilities (IP QoS Function)
   - VPN over Wireless LAN
   - ISDN Backup Facilities for Vi and VGi models.

[END oF FILE]